From BananaPro/Pi
Jump to: navigation, search

Other languages:
English • ‎中文(简体)‎


150M Wireless USB Adapter comply with IEEE 802.11n(Draft 2.0),IEEE 802.11g,IEEE 802.11b standard.It has the advantage of wireless transmission rates of up to 150Mbps,Built-in smart antennas providing better wireless performance,stability,and wireless coverage.The product supports 64/128/152 bit WEP encryption,and WPA/WPA2,WPA-PSK/WPA2-PSK and other advanced encryption, security mechanism,and also the QSS fast security setting TRL8188CUS function,in line with WPS,can easily improve wireless security.In addition,the product has priority service functions to ensure priority processing video,voice and other bandwidth-intensive data.The product is compatible with 11g/n/b products.

General specifications

Brand GRIS
Modle GE-LW04-3L5T
Network adapter Interface USB Interface(2.0 Frequency range 2.4 ~ 2.4835GHz transmission rate)
Adaptation Network Type Ethernet
11n OFDM with PSK,BPSK,16-QA,64-QAM(up to 150Mbps)
11b 1/2/5.5/11Mbps
RF power 20dBi(max)
Wireless Gain 2dBi(build-in)
Dimensions 68*20*8.7mm
Environmental operating temperature 0℃ to 40℃
Working humidity 10% to 90%RH RH non-condensing
Strorage humidity 5% to 90%RH RH non-condensing
Supported operating systems Win2000/2003,Winxp,Vista32/64,Wince5.0/6.0,Win7/8/10,Linux,Mac(10.3/10.4/10.5)
Supports standard and protocol IEEE 802.11n(Draft 2.0)、IEEE 802.11g、IEEE 802.11b standard,CSMA/CA with ACK bus types

WIFI station mode

Step 1: Insert the wireless adapter into LeMaker Guitar usb interface.
Step 2: Download rt2l8192cufw_TSMC.bin file.Move rtll8192cufw_TSMC.bin to the /lib/firmware/rtlwifi directory then restart.
NOTE: On V1601 or newer released image, this firmware has already included in the system, so you can skip this step.

sudo wget http://mirror.lemaker.org/RTL8192CUS_Firmware.7z
7z e  RTL8192CUS_Firmware.7z
sudo mkdir -p /lib/firmware/rtlwifi
sudo mv rtl8192cufw_TMSC.bin /lib/firmware/rtlwifi/
sudo reboot

Step 3: Use the command below to check the WIFI module which has been loaded on,and it shows the wlan2 on my LeMaker Guitar.Different devices may display various.

ifconfig -a

Step 4: Edit the /etc/network/interfaces file like this:

allow-hotplug wlanX #X maybe 0.1.2.....
iface wlanX inet manual 
wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
iface default inet dhcp

Please modify wlanx according to the actual situation.

Step 5: Config /etc/wpa_supplicant/wpa_supplicant.conf file

sudo vim /etc/wpa_supplicant/wpa_supplicant.conf
GROUP=netdev update_config=1

Step 6: Edit /etc/group
Add user lemaker to the group netdev, like this:


Step 7: Restart network

sudo /etc/init.d/networking restart

And then you can refer to http://wiki.lemaker.org/LeMaker_Guitar:WiFi_configuration#Lemuntu to configure WIFI with wpa_gui.

WIFI AP mode

Step 1: Download udhcp

apt-get install udhcpd

Step 2: Edit /etc/hostapd/hostapd.conf file

sudo apt-get install vim 
sudo vim /etc/hostapd/hostapd.conf
interface=wlanx # x maybe 0.1.2...

ssid is WIFI name and wpa_passphrase is password name.
Step 3: Config /etc/udhcpd.conf

sudo vim /etc/udhcpd.conf
#The start and end of the IP lease block
start    #default:
end   #default:
#The interface that udhcpd will use
interface   wlanx     #default: eth0
option  subnet
opt     router
opt     wins
option  dns
option  domain  local
option  lease   864000

Step 4: Execute the following command after reboot.
Enable udhcp service

udhcpd /etc/udhcpd.conf

Run hostapd

hostapd –B /etc/hostapd/hostapd.conf

Now check whether your wifi hotspot can be shared with other devices or not.(The wifi name is WIFI_ap_test at here)

See also

  1. http://wiki.lemaker.org/LeMaker_Guitar:WiFi_configuration